Cisco CCNA / CCNP Certification Exam Tutorial: ISDN And Multilink PPP
482
Computers > Computer Certification
Mar 1, 2007
Chris Bryant, CCIE #12933
Cisco CCNA / CCNP Certification Exam Tutorial: ISDN And Multilink PPP
ISDN is a huge topic on both your Cisco CCNA and BCRAN CCNP exams. While many ISDN topics seem straightforward, it?s the details that make the difference in the exam room and working with ISDN in production networks. Configuring and troubleshooting multilink PPP is just one of the skills you?ll need to pass both of these demanding exams.
With BRI, we've got two B-channels to carry data, and both of them have a 64-kbps capacity. You might think it would be a good idea to have both channels in operation before one reaches capacity, and it is a great idea Problem is, it's not a default behavior of ISDN. The second b-channel will not begin to carry traffic until the first one reaches capacity.
With Multilink PPP (MLP), a bandwidth capacity can be set that will allow the second b-channel to bear data before the first channel reaches capacity. The configuration for MLP is simple, but often misconfigured. We'll use our good friend IOS Help to verify the measurement this command uses.
Enabling MLP is a three-step process:
Enable PPP on the link
Enable MLP with the command ppp multilink
Define the threshold at which the second b-channel should start carrying data with the dialer load-threshold command.
Let's say you wanted the second b-channel to start carrying data when the first channel reaches 75% of capacity. It would make sense that the command to do so would be dialer load-threshold 75... but it's not.
R1(config)#int bri0
R1(config-if)#ppp multilink
R1(config-if)#dialer load-threshold ?
Load threshold to place another call
The dialer load-threshold value is based on 255, not 100. To have this command bring the line up at a certain percentage, multiply that percentage in decimal format by 255. Below, I multiplied 255 by .75 (75%) to arrive at 191.
R1(config-if)#dialer load-threshold 191 ?
either Threshold decision based on max of inbound and outbound traffic
inbound Threshold decision based on inbound traffic only
outbound Threshold decision based on outbound traffic only
R1(config-if)#dialer load-threshold 191 either
As illustrated by IOS Help in the above configuration, dialer load-threshold has additional options as well. You can configure the interface to consider only incoming, outgoing, or all traffic when calculating when to bring the next channel up.
Configuring Multilink PPP is just one of the skills you?ll need to earn your CCNA and pass the CCNP BCRAN exam. Don?t underestimate ISDN on Cisco?s certification exams! Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website. For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage!
With BRI, we've got two B-channels to carry data, and both of them have a 64-kbps capacity. You might think it would be a good idea to have both channels in operation before one reaches capacity, and it is a great idea Problem is, it's not a default behavior of ISDN. The second b-channel will not begin to carry traffic until the first one reaches capacity.
With Multilink PPP (MLP), a bandwidth capacity can be set that will allow the second b-channel to bear data before the first channel reaches capacity. The configuration for MLP is simple, but often misconfigured. We'll use our good friend IOS Help to verify the measurement this command uses.
Enabling MLP is a three-step process:
Enable PPP on the link
Enable MLP with the command ppp multilink
Define the threshold at which the second b-channel should start carrying data with the dialer load-threshold command.
Let's say you wanted the second b-channel to start carrying data when the first channel reaches 75% of capacity. It would make sense that the command to do so would be dialer load-threshold 75... but it's not.
R1(config)#int bri0
R1(config-if)#ppp multilink
R1(config-if)#dialer load-threshold ?
Load threshold to place another call
The dialer load-threshold value is based on 255, not 100. To have this command bring the line up at a certain percentage, multiply that percentage in decimal format by 255. Below, I multiplied 255 by .75 (75%) to arrive at 191.
R1(config-if)#dialer load-threshold 191 ?
either Threshold decision based on max of inbound and outbound traffic
inbound Threshold decision based on inbound traffic only
outbound Threshold decision based on outbound traffic only
R1(config-if)#dialer load-threshold 191 either
As illustrated by IOS Help in the above configuration, dialer load-threshold has additional options as well. You can configure the interface to consider only incoming, outgoing, or all traffic when calculating when to bring the next channel up.
Configuring Multilink PPP is just one of the skills you?ll need to earn your CCNA and pass the CCNP BCRAN exam. Don?t underestimate ISDN on Cisco?s certification exams! Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website. For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
Policy routing is a major topic on your BSCI exam, and you'll find quite a bit of policy routing going on in today's production networks. But what exactly is policy routing? Policy-based routing, generally referred to as "policy routing", is the
Category:
To earn your Cisco CCNA certification and pass the BSCI CCNP exam, you have to know your protocol basics like the back of your hand! To help you review these important concepts, here's a quick look at the basics of RIPv1, RIPv2, IGRP, and
Category:
Earning your CCNP certification and ing the BSCI exam depends on knowing the details of many Cisco technologies, ISIS chief among them. To help you prepare for exam success, here's a list of ISIS terminology and basic concepts that will help you
Category:
One f the first things yu learned abut Frame is that the LMI als serves as a keepalive, r a heartbeat - and if three cnsecutive LMIs are missed, the line prtcl ges dwn. There's a limitatin t LMI as a keepalive, thugh. The LMI is exchanged
Category:
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you?ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs).
Category:
Not only is your CCNA exam going to have questions on VLAN trunking protocol, almost any network that has more than one VLAN is going to have VTP running. Whether you're planning on passing the CCNA exam or just brushing up on your networking skills,
Category:
To ern your CCNA or CCNP certifiction, you've got to understnd the bsics of trunking. This isn't just CCNA topic - you must hve n dvnced understnding of trunking nd etherchnnels to pss the BCMSN exm nd ern your CCNP s well. Before we
Category:
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very
Category:
To pass the BSCI exam an earn your CCNP, you've got to keep a lot of etails in min. It's easy to overlook the "simpler" protocols an services such as static routing an istance vector protocols. With this in min, here's a quick review of some
Category:
To pass your CCNA exam and earn this coveted certification, you must understand the details of port-based authentication. This knowledge has a great deal of value in production networks as well, since this authentication scheme is regularly implemented.
Category:
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by
Category:
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're gog to fail an exam. It's happened to almost all of us, yours truly cluded. What you have to keep
Category:
ISDN is a huge topic on both your Cisco CCNA and BCRAN CCNP exams. While many ISDN topics seem straightforward, it?s the details that make the difference in the exam room and working with ISDN in production networks. Configuring and troubleshooting
Category:
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this
Category:
To pass he BCMSN exam and earn your CCNP cerificaion, you've go o know HSRP inside and ou. While he operaion and basic commands of HSRP are prey simple, here are some imporan deails ha are easily overlooked bu are vial in geing HSRP
Category:
Dialer Watch is a vital part of your CCNA and CCNP studies, particularly for the BCRAN exam, but it's one of the most misunderstood technologies as well. To help you pass the CCNA and CCNP certification exams, here's a detailed look at Dialer
Category:
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that
Category:
Your BCMSN and CCNP studies will include mastering the details of Spanning Tree Protocol (STP). While you learned some of these details in your CCNA studies, quite a bit of it may be new to you. Before going on to the intermediate and advanced STP
Category:
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a
Category:
Other links at Computers > Computer Certification
Dialer Watch is a vital part of your CCNA and CCNP studies, particularly for the BCRAN exam, but it's one of the most misunderstood technologies as well. To help you pass the CCNA and CCNP certification exams, here's a detailed look at Dialer
Category:
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very
Category:
To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
To ern your CCNA or CCNP certifiction, you've got to understnd the bsics of trunking. This isn't just CCNA topic - you must hve n dvnced understnding of trunking nd etherchnnels to pss the BCMSN exm nd ern your CCNP s well. Before we
Category:
Site Sponsor
Directory Statistics
Articles: 68214
Categories: 501
Yahoo Entertainment
