Cisco CCNA Certification Exam Tutorial: Configuring Dialer Profiles
4802
Computers > Computer Certification
Mar 1, 2007
Chris Bryant
Cisco CCNA Certification Exam Tutorial: Configuring Dialer Profiles
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer profiles.
Dialer Profiles allow different dialing information to be configured onto logical interfaces. The logical interfaces may have different dialing destinations, different remote router names, etc., but they?ll be using the same physical interface.
Dialer strings are used on dialer profiles. Note that each logical interface has a different IP address, a different remote router to dial, and a different dialer string, but they will be using the same physical interface to dial out. The commands dialer pool and dialer pool-member are used to link the logical and physical interfaces. The number following each command must match for the logical interface to correctly bind to the physical interface.
R1(config)#interface dialer0
R1(config-if)#ip address 172.16.1.1 255.255.255.0
R1(config-if)#encapsulation ppp
R1(config-if)#dialer remote-name Remote0
R1(config-if)#dialer pool 1
< places logical interface into dialer pool >
R1(config-if)#dialer string 5551212
< number dialed to contact router Remote0 >
R1(config-if)#dialer-group 1
< links logical interface to dialer-list 1 >
R1(config)#interface dialer1
R1(config-if)#ip address 172.16.1.2 255.255.255.0
R1(config-if)#encapsulation ppp
R1(config-if)#dialer remote-name Remote1
R1(config-if)#dialer pool 1
R1(config-if)#dialer string 5551234
R1(config-if)#dialer-group 1
R1(config)#interface bri0
R1(config-if)#no ip address
< With dialer profiles, IP addresses are assigned to logical interfaces. >
R1(config-if)#encapsulation ppp
< The encapsulation type is place on both the logical and physical interfaces.>
R1(config-if)#dialer pool-member 1
< The number associated with this command should match the number configured with the dialer pool number on the logical dialer interfaces. >
R1(config-if)#isdn spid1 0835866101
R1(config-if)#isdn spid2 0835866301
When configuring dialer profiles, the encapsulation type should be placed on both the physical BRI interface and the logical dialer interfaces. The SPIDs are configured on the physical interface as well.
Configuring dialer profiles can be a little tricky at first, and the best way to master this skill is to get real hands-on practice in your own CCNA / CCNP home lab or a rack rental service. Either way, hands-on is the best practice. Best of luck in your CCNA studies!
Dialer Profiles allow different dialing information to be configured onto logical interfaces. The logical interfaces may have different dialing destinations, different remote router names, etc., but they?ll be using the same physical interface.
Dialer strings are used on dialer profiles. Note that each logical interface has a different IP address, a different remote router to dial, and a different dialer string, but they will be using the same physical interface to dial out. The commands dialer pool and dialer pool-member are used to link the logical and physical interfaces. The number following each command must match for the logical interface to correctly bind to the physical interface.
R1(config)#interface dialer0
R1(config-if)#ip address 172.16.1.1 255.255.255.0
R1(config-if)#encapsulation ppp
R1(config-if)#dialer remote-name Remote0
R1(config-if)#dialer pool 1
< places logical interface into dialer pool >
R1(config-if)#dialer string 5551212
< number dialed to contact router Remote0 >
R1(config-if)#dialer-group 1
< links logical interface to dialer-list 1 >
R1(config)#interface dialer1
R1(config-if)#ip address 172.16.1.2 255.255.255.0
R1(config-if)#encapsulation ppp
R1(config-if)#dialer remote-name Remote1
R1(config-if)#dialer pool 1
R1(config-if)#dialer string 5551234
R1(config-if)#dialer-group 1
R1(config)#interface bri0
R1(config-if)#no ip address
< With dialer profiles, IP addresses are assigned to logical interfaces. >
R1(config-if)#encapsulation ppp
< The encapsulation type is place on both the logical and physical interfaces.>
R1(config-if)#dialer pool-member 1
< The number associated with this command should match the number configured with the dialer pool number on the logical dialer interfaces. >
R1(config-if)#isdn spid1 0835866101
R1(config-if)#isdn spid2 0835866301
When configuring dialer profiles, the encapsulation type should be placed on both the physical BRI interface and the logical dialer interfaces. The SPIDs are configured on the physical interface as well.
Configuring dialer profiles can be a little tricky at first, and the best way to master this skill is to get real hands-on practice in your own CCNA / CCNP home lab or a rack rental service. Either way, hands-on is the best practice. Best of luck in your CCNA studies!
Article Source: http://www.articlerich.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
To pass the BSCI exam, you need to know the difference between IRDP and HSRP. While they have the same basic function, the operation and configuration of each are totally different. The aim of both is to allow hosts to quickly discover a
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
OSPF route ibution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route
Category:
While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that's on one side of a router with other subnets on the other side.
Category:
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
QoS - Quality o Service - is a huge topic on both the BCMSN exam and real-world networks. QoS is so big today that Cisco's created separate specialist certiications that cover nothing but QoS! It can be an overwhelming topic at irst, but master the
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
EIGRP is a major subject of the CCNA exam, and Cisco goes into even more detail with EIGRP on your CCNP exams. Part of that detail is the purpose and configuration of EIGRP stub routers. A problem with EIGRP comes in when a successor is
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
CCNA exam success deends artially on knowing the details of ISDN, and there are lenty of them! To hel you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They hel in the real world, too ? and there are still
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can
Category:
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer
Category:
Other links at Computers > Computer Certification
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
One f the first things yu learned abut Frame is that the LMI als serves as a keepalive, r a heartbeat - and if three cnsecutive LMIs are missed, the line prtcl ges dwn. There's a limitatin t LMI as a keepalive, thugh. The LMI is exchanged
Category:
When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that
Category:
Site Sponsor
Directory Statistics
Articles: 68234
Categories: 501
Yahoo Entertainment
