Cisco CCNA / CCNP Home Lab Tutorial: The 2501 Router
4799
Computers > Computer Certification
Mar 1, 2007
Chris Bryant
Cisco CCNA / CCNP Home Lab Tutorial: The 2501 Router
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or sued. The key to becoming a true CCNA and CCNP is assembling your own Cisco home lab.
You don't have to spend a lot of money to do so; used Cisco equipment is cheaper than ever. It's robust as well - I've bought literally hundreds of used routers and switches over the years and have had very few problems. I owe much of my skill to practicing configurations and troubleshooting in my own home lab.
2501 routers are fantastic for CCNA and CCNP home labs. They come with two serial interfaces, allowing you to connect one interface directly to another router (you'll need a DTE/DCE cable for that, too) while connecting another to a frame relay switch if you like. If you don't have a frame relay switch, you can connect a 2501 directly to two other routers via the serial interfaces.
You also have an AUI port, which requires a transceiver to operate as your Ethernet interface. Transceivers are pretty cheap and readily available from Cisco resellers and ebay vendors, so pick one up for each 2503 you decide to buy.
2501 routers don't come with BRI interfaces, but not every router in your lab has to be ISDN-ready. If you choose not to have ISDN in your lab at all, 2501s are the way to go. If you do want to run ISDN and have an ISDN simulator device, you can get two 2503s and the rest of your routers can be 2501.
All in all, 2501 routers are great for your CCNA / CCNP home lab. They cost less than $100 each on ebay, so they're also very affordable. There's no better training than training on your own CCNA or CCNP home lab, and you can always sell the equipment later if you like. Basically, you're renting the routers and switches, and the experience you get by working with the real deal is invaluable.
You don't have to spend a lot of money to do so; used Cisco equipment is cheaper than ever. It's robust as well - I've bought literally hundreds of used routers and switches over the years and have had very few problems. I owe much of my skill to practicing configurations and troubleshooting in my own home lab.
2501 routers are fantastic for CCNA and CCNP home labs. They come with two serial interfaces, allowing you to connect one interface directly to another router (you'll need a DTE/DCE cable for that, too) while connecting another to a frame relay switch if you like. If you don't have a frame relay switch, you can connect a 2501 directly to two other routers via the serial interfaces.
You also have an AUI port, which requires a transceiver to operate as your Ethernet interface. Transceivers are pretty cheap and readily available from Cisco resellers and ebay vendors, so pick one up for each 2503 you decide to buy.
2501 routers don't come with BRI interfaces, but not every router in your lab has to be ISDN-ready. If you choose not to have ISDN in your lab at all, 2501s are the way to go. If you do want to run ISDN and have an ISDN simulator device, you can get two 2503s and the rest of your routers can be 2501.
All in all, 2501 routers are great for your CCNA / CCNP home lab. They cost less than $100 each on ebay, so they're also very affordable. There's no better training than training on your own CCNA or CCNP home lab, and you can always sell the equipment later if you like. Basically, you're renting the routers and switches, and the experience you get by working with the real deal is invaluable.
Article Source: http://www.articlerich.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
CCNA exam success deends artially on knowing the details of ISDN, and there are lenty of them! To hel you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They hel in the real world, too ? and there are still
Category:
OSPF route ibution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route
Category:
EIGRP is a major subject of the CCNA exam, and Cisco goes into even more detail with EIGRP on your CCNP exams. Part of that detail is the purpose and configuration of EIGRP stub routers. A problem with EIGRP comes in when a successor is
Category:
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can
Category:
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
QoS - Quality o Service - is a huge topic on both the BCMSN exam and real-world networks. QoS is so big today that Cisco's created separate specialist certiications that cover nothing but QoS! It can be an overwhelming topic at irst, but master the
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that's on one side of a router with other subnets on the other side.
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer
Category:
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both
Category:
To pass the BSCI exam, you need to know the difference between IRDP and HSRP. While they have the same basic function, the operation and configuration of each are totally different. The aim of both is to allow hosts to quickly discover a
Category:
Other links at Computers > Computer Certification
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
One f the first things yu learned abut Frame is that the LMI als serves as a keepalive, r a heartbeat - and if three cnsecutive LMIs are missed, the line prtcl ges dwn. There's a limitatin t LMI as a keepalive, thugh. The LMI is exchanged
Category:
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're gog to fail an exam. It's happened to almost all of us, yours truly cluded. What you have to keep
Category:
ISDN is a huge topic on both your Cisco CCNA and BCRAN CCNP exams. While many ISDN topics seem straightforward, it?s the details that make the difference in the exam room and working with ISDN in production networks. Configuring and troubleshooting
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
Site Sponsor
Directory Statistics
Articles: 68214
Categories: 501
Yahoo Entertainment
