Cisco CCNA Certification Exam Tutorial: ISDN Details You Must Know
4795
Computers > Computer Certification
Mar 1, 2007
Chris Bryant
Cisco CCNA Certification Exam Tutorial: ISDN Details You Must Know
CCNA exam success depends partially on knowing the details of ISDN, and there are plenty of them! To help you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They help in the real world, too ? and there are still plenty of ISDN networks out there!
The Cisco-proprietary version of HDLC is the default encapsulation type for serial and ISDN interfaces.
R2#show interface serial0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
While there?s only one D-channel in BRI, PRI (US) and PRI (EU), the bandwidth of that D-channel does vary from BRI to PRI. It?s 16 kbps in BRI and 64 kbps in both PRI versions.
The global command isdn switch-type must be configured before you can even begin to have ISDN work. show isdn status will tell you whether or not you?ve done this correctly.
R2#show isdn status
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
PAP allows passwords to be different; CHAP requires that they be the same.
PAP requires the ?ppp pap sent-username? interface-level command. CHAP has no equivalent command.
Define interesting traffic with dialer-list and link that list to the interface with dialer-group.
R2#conf t
R2(config)#dialer-list 1 proto ip permit
R2(config)#int bri0
R2(config-if)#dialer-group 1
The dialer idle-timeout value is expressed in seconds, not minutes. (Even IOS Help isn?t totally clear on this.)
R2(config)#int bri0
R2(config-if)#dialer-group 1
R2(config-if)#dialer idle-timeout ?
Idle timeout before disconnecting a call
R2(config-if)#dialer idle-timeout 120
Dialer map maps a remote IP address to a remote phone number. You never dial the local router?s phone number.
dialer load-threshold requires the ppp multilink command to be configured, and the value of dialer load-threshold is expressed as a ratio of 255, NOT 100. For example, if you want the second b-channel to come up when the first reaches 50% of capacity, the value to express with dialer load-threshold would be 50% of 255 ? which equals 127.
R2(config)#int bri0
R2(config-if)#encap ppp
R2(config-if)#ppp multilink
R2(config-if)#dialer load-threshold ?
Load threshold to place another call
Success on the CCNA exam depends on knowing the details. Keep studying, keep practicing on real Cisco routers and switches, keep a positive attitude, and you're on your way to CCNA exam success!
The Cisco-proprietary version of HDLC is the default encapsulation type for serial and ISDN interfaces.
R2#show interface serial0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
While there?s only one D-channel in BRI, PRI (US) and PRI (EU), the bandwidth of that D-channel does vary from BRI to PRI. It?s 16 kbps in BRI and 64 kbps in both PRI versions.
The global command isdn switch-type must be configured before you can even begin to have ISDN work. show isdn status will tell you whether or not you?ve done this correctly.
R2#show isdn status
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
PAP allows passwords to be different; CHAP requires that they be the same.
PAP requires the ?ppp pap sent-username? interface-level command. CHAP has no equivalent command.
Define interesting traffic with dialer-list and link that list to the interface with dialer-group.
R2#conf t
R2(config)#dialer-list 1 proto ip permit
R2(config)#int bri0
R2(config-if)#dialer-group 1
The dialer idle-timeout value is expressed in seconds, not minutes. (Even IOS Help isn?t totally clear on this.)
R2(config)#int bri0
R2(config-if)#dialer-group 1
R2(config-if)#dialer idle-timeout ?
Idle timeout before disconnecting a call
R2(config-if)#dialer idle-timeout 120
Dialer map maps a remote IP address to a remote phone number. You never dial the local router?s phone number.
dialer load-threshold requires the ppp multilink command to be configured, and the value of dialer load-threshold is expressed as a ratio of 255, NOT 100. For example, if you want the second b-channel to come up when the first reaches 50% of capacity, the value to express with dialer load-threshold would be 50% of 255 ? which equals 127.
R2(config)#int bri0
R2(config-if)#encap ppp
R2(config-if)#ppp multilink
R2(config-if)#dialer load-threshold ?
Load threshold to place another call
Success on the CCNA exam depends on knowing the details. Keep studying, keep practicing on real Cisco routers and switches, keep a positive attitude, and you're on your way to CCNA exam success!
Article Source: http://www.articlerich.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that's on one side of a router with other subnets on the other side.
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
OSPF route ibution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route
Category:
EIGRP is a major subject of the CCNA exam, and Cisco goes into even more detail with EIGRP on your CCNP exams. Part of that detail is the purpose and configuration of EIGRP stub routers. A problem with EIGRP comes in when a successor is
Category:
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both
Category:
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can
Category:
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
QoS - Quality o Service - is a huge topic on both the BCMSN exam and real-world networks. QoS is so big today that Cisco's created separate specialist certiications that cover nothing but QoS! It can be an overwhelming topic at irst, but master the
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
To pass the BSCI exam, you need to know the difference between IRDP and HSRP. While they have the same basic function, the operation and configuration of each are totally different. The aim of both is to allow hosts to quickly discover a
Category:
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
CCNA exam success deends artially on knowing the details of ISDN, and there are lenty of them! To hel you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They hel in the real world, too ? and there are still
Category:
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer
Category:
Other links at Computers > Computer Certification
Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very
Category:
When targeting small businesses that are in the sweet spot size, what IT certifications do you typically need? One thing to keep in mind is that you are not selling to a real IT manager in most cases. Remember Who You Are Selling Your
Category:
To pass he BCMSN exam and earn your CCNP cerificaion, you've go o know HSRP inside and ou. While he operaion and basic commands of HSRP are prey simple, here are some imporan deails ha are easily overlooked bu are vial in geing HSRP
Category:
Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by
Category:
To ern your CCNA or CCNP certifiction, you've got to understnd the bsics of trunking. This isn't just CCNA topic - you must hve n dvnced understnding of trunking nd etherchnnels to pss the BCMSN exm nd ern your CCNP s well. Before we
Category:
Site Sponsor
Directory Statistics
Articles: 68228
Categories: 501
Yahoo Entertainment
