Cisco CCNP / BCMSN Exam Tutorial: Multicasting And The RPF Check
4794
Computers > Computer Certification
Mar 1, 2007
Chris Bryant
Cisco CCNP / BCMSN Exam Tutorial: Multicasting And The RPF Check
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can throw you at first. I speak from experience that multicasting is like any other Cisco technology - learn the basics, master the fundamentals, and then build your skills on that foundation.
One such fundamental is the RPF Check, or Reverse Path Forwarding Check.
A fundamental difference between unicasting and multicasting is that a unicast is routed by sending it toward the destination, while a multicast is routed by sending it away from its source.
"toward the destination" and "away from its source" sound like the same thing, but they're not. A unicast is going to follow a single path from source to destination. The only factor the routers care about is the destination IP address - the source IP address isn't a factor.
With multicast routing, the destination is a multicast IP group address. It's the multicast router's job to decide which paths will lead back to the source (upstream) and which paths are downstream from the source. Reverse Path Forwarding refers to the router's behavior of sending multicast packets away from the source rather than toward a specific destination.
The RPF Check is run against any incoming multicast packet. The multicast router examines the interface that the packet arrived on. If the packet comes in on an upstream interface - that is, an interface found on the reverse path that leads back to the source - the packet passes the check and will be forwarded. If the packet comes in on any other interface, the packet is dropped.
The RPF Check serves to verify the integrity of your multicasting network, and also serves as a reminder that the basic operation of multicasting is a lot different than unicasting!
One such fundamental is the RPF Check, or Reverse Path Forwarding Check.
A fundamental difference between unicasting and multicasting is that a unicast is routed by sending it toward the destination, while a multicast is routed by sending it away from its source.
"toward the destination" and "away from its source" sound like the same thing, but they're not. A unicast is going to follow a single path from source to destination. The only factor the routers care about is the destination IP address - the source IP address isn't a factor.
With multicast routing, the destination is a multicast IP group address. It's the multicast router's job to decide which paths will lead back to the source (upstream) and which paths are downstream from the source. Reverse Path Forwarding refers to the router's behavior of sending multicast packets away from the source rather than toward a specific destination.
The RPF Check is run against any incoming multicast packet. The multicast router examines the interface that the packet arrived on. If the packet comes in on an upstream interface - that is, an interface found on the reverse path that leads back to the source - the packet passes the check and will be forwarded. If the packet comes in on any other interface, the packet is dropped.
The RPF Check serves to verify the integrity of your multicasting network, and also serves as a reminder that the basic operation of multicasting is a lot different than unicasting!
Article Source: http://www.articlerich.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
To pass the BSCI exam, you need to know the difference between IRDP and HSRP. While they have the same basic function, the operation and configuration of each are totally different. The aim of both is to allow hosts to quickly discover a
Category:
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer
Category:
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both
Category:
QoS - Quality o Service - is a huge topic on both the BCMSN exam and real-world networks. QoS is so big today that Cisco's created separate specialist certiications that cover nothing but QoS! It can be an overwhelming topic at irst, but master the
Category:
OSPF route ibution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route
Category:
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can
Category:
CCNA exam success deends artially on knowing the details of ISDN, and there are lenty of them! To hel you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They hel in the real world, too ? and there are still
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that's on one side of a router with other subnets on the other side.
Category:
EIGRP is a major subject of the CCNA exam, and Cisco goes into even more detail with EIGRP on your CCNP exams. Part of that detail is the purpose and configuration of EIGRP stub routers. A problem with EIGRP comes in when a successor is
Category:
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
Other links at Computers > Computer Certification
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
ISDN is a huge topic on both your Cisco CCNA and BCRAN CCNP exams. While many ISDN topics seem straightforward, it?s the details that make the difference in the exam room and working with ISDN in production networks. Configuring and troubleshooting
Category:
Dialer Watch is a vital part of your CCNA and CCNP studies, particularly for the BCRAN exam, but it's one of the most misunderstood technologies as well. To help you pass the CCNA and CCNP certification exams, here's a detailed look at Dialer
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
Site Sponsor
Directory Statistics
Articles: 68228
Categories: 501
Yahoo Entertainment
