Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
4788
Computers > Computer Certification
Mar 1, 2007
Chris Bryant
Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics.
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
R1#show ip ospf
Routing Process "ospf 1" with ID 1.1.1.1
Supports only single TOS(TOS0) routes
Supports opaque LSA
It is an area border and autonomous system boundary router
Redistributing External Routes from,
connected, includes subnets in redistribution
rip, includes subnets in redistribution
When redistributing RIP into OSPF, the ?subnets" option is needed to include subnets in redistribution. When redistributing OSPF into RIP, a seed metric must be specified. (OSPF gives redistributed routes a default metric of 20 ? this can be changed, but a seed metric does not have to be set.)
R1(config)#router ospf 1
R1(config-router)#redistribute connected
% Only classful networks will be redistributed
R1(config-router)#redistribute connected subnets
R1(config-router)#redistribute rip subnets
R1(config-router)#router rip
R1(config-router)#redistribute connected metric 1
R1(config-router)#redistribute ospf 1 metric 1
By default, routes redistributed into OSPF are marked as E2 routes. The metric for these routes reflects only the cost of the path from the ASBR to the destination network and does not include the cost of the path from the local router to the ASBR. By contrast, E1 routes include the cost of the entire path from the local router to the destination network.
O E2 5.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
6.0.0.0/32 is subnetted, 1 subnets
O E2 6.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
172.12.0.0/16 is variably subnetted, 2 subnets, 2 masks
O E2 172.12.21.0/30 [110/20] via 172.34.34.3, 00:33:32, Ethernet0
O E2 7.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
15.0.0.0/24 is subnetted, 1 subnets
O E2 15.1.1.0 [110/20] via 172.34.34.3, 00:33:32, Ethernet0
To redistribute routes into OSPF and mark them as E1 upon redistribution, use the metric-type option with the redistribution command.
R1(config)#router ospf 1
R1(config-router)#redistribute rip subnets metric-type ?
1 Set OSPF External Type 1 metrics
2 Set OSPF External Type 2 metrics
R1(config-router)#redistribute rip subnets metric-type 1
Look at the same two routes in R4's routing table, which are now displayed as E1 routes:
O E1 5.1.1.1 [110/94] via 172.34.34.3, 00:04:13, Ethernet0
6.0.0.0/32 is subnetted, 1 subnets
O E1 6.1.1.1 [110/94] via 172.34.34.3, 00:04:14, Ethernet0
BSCI exam success and earning your CCNP certification depends on knowing the details, and there are plenty of details involved in OSPF route redistribution! Keep studying, practice different scenarios in your CCNA / CCNP home lab or rack rental, and you'll master these details and pass the exam!
To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
R1#show ip ospf
Routing Process "ospf 1" with ID 1.1.1.1
Supports only single TOS(TOS0) routes
Supports opaque LSA
It is an area border and autonomous system boundary router
Redistributing External Routes from,
connected, includes subnets in redistribution
rip, includes subnets in redistribution
When redistributing RIP into OSPF, the ?subnets" option is needed to include subnets in redistribution. When redistributing OSPF into RIP, a seed metric must be specified. (OSPF gives redistributed routes a default metric of 20 ? this can be changed, but a seed metric does not have to be set.)
R1(config)#router ospf 1
R1(config-router)#redistribute connected
% Only classful networks will be redistributed
R1(config-router)#redistribute connected subnets
R1(config-router)#redistribute rip subnets
R1(config-router)#router rip
R1(config-router)#redistribute connected metric 1
R1(config-router)#redistribute ospf 1 metric 1
By default, routes redistributed into OSPF are marked as E2 routes. The metric for these routes reflects only the cost of the path from the ASBR to the destination network and does not include the cost of the path from the local router to the ASBR. By contrast, E1 routes include the cost of the entire path from the local router to the destination network.
O E2 5.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
6.0.0.0/32 is subnetted, 1 subnets
O E2 6.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
172.12.0.0/16 is variably subnetted, 2 subnets, 2 masks
O E2 172.12.21.0/30 [110/20] via 172.34.34.3, 00:33:32, Ethernet0
O E2 7.1.1.1 [110/20] via 172.34.34.3, 00:33:21, Ethernet0
15.0.0.0/24 is subnetted, 1 subnets
O E2 15.1.1.0 [110/20] via 172.34.34.3, 00:33:32, Ethernet0
To redistribute routes into OSPF and mark them as E1 upon redistribution, use the metric-type option with the redistribution command.
R1(config)#router ospf 1
R1(config-router)#redistribute rip subnets metric-type ?
1 Set OSPF External Type 1 metrics
2 Set OSPF External Type 2 metrics
R1(config-router)#redistribute rip subnets metric-type 1
Look at the same two routes in R4's routing table, which are now displayed as E1 routes:
O E1 5.1.1.1 [110/94] via 172.34.34.3, 00:04:13, Ethernet0
6.0.0.0/32 is subnetted, 1 subnets
O E1 6.1.1.1 [110/94] via 172.34.34.3, 00:04:14, Ethernet0
BSCI exam success and earning your CCNP certification depends on knowing the details, and there are plenty of details involved in OSPF route redistribution! Keep studying, practice different scenarios in your CCNA / CCNP home lab or rack rental, and you'll master these details and pass the exam!
Article Source: http://www.articlerich.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!
Write a Review
Add to My Favorite
Refer it to Friend
Report Article
Other links owned by this user
OSPF route ibution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route
Category:
While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that's on one side of a router with other subnets on the other side.
Category:
CCNA exam success deends artially on knowing the details of ISDN, and there are lenty of them! To hel you review for your CCNA exam, here are a few ISDN details that you must know on exam day. (They hel in the real world, too ? and there are still
Category:
The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both
Category:
Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can
Category:
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
To pass the BSCI exam, you need to know the difference between IRDP and HSRP. While they have the same basic function, the operation and configuration of each are totally different. The aim of both is to allow hosts to quickly discover a
Category:
Your BSCI exam and CCNP certification success depend on mastering BGP, and a ig part of that is knowing how and when to use the many BGP attriutes. And for those of you with an eye on the CCIE, elieve me - you've got to know BGP attriutes like the
Category:
EIGRP is a major subject of the CCNA exam, and Cisco goes into even more detail with EIGRP on your CCNP exams. Part of that detail is the purpose and configuration of EIGRP stub routers. A problem with EIGRP comes in when a successor is
Category:
RIP isn't exactly the most complex routing protocol on the CCNA exam, but that makes it easy to overlook some of the important you must keep in mind in order to pass the exam! To help you review for the exam, here are just a few of those
Category:
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router. Frame Relay VCs use
Category:
To pass e CCNA exam, you've got to know how to work wi IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure
Category:
To be truly prepared for your CCNA and CCNP exams, you need real hands-on experience with real Cisco routers and switches. However, a production network is a really bad place to practice your configurations, but an excellent way to get fired and/or
Category:
QoS - Quality o Service - is a huge topic on both the BCMSN exam and real-world networks. QoS is so big today that Cisco's created separate specialist certiications that cover nothing but QoS! It can be an overwhelming topic at irst, but master the
Category:
QoS is a big topic on your BCMSN and CCNP exams, and for good reason. As more and more traffic flows through today's networks, accurately plying QoS to both your routers and switches becomes more important. Note the phrase "accurately
Category:
Ever since you picked up your first CCNA book, you've heard about multicasting, ten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've
Category:
Other links at Computers > Computer Certification
I know from experience that part of the excitement and anxiety of putting together your own CCNA / CCNP home lab is deciding what to buy! While you can make a workable home lab out of almost any combination of Cisco routers and switches, some routers
Category:
Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're gog to fail an exam. It's happened to almost all of us, yours truly cluded. What you have to keep
Category:
If a Layer Two switch doesn't have the capabilities to run IGMP Snooping, it will be able to run CGMP - Cisco Group Membership Protocol. CGMP allows the multicast router to work with the Layer Two switch to eliminate unnecessary multicast forwarding.
Category:
When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you?ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs).
Category:
* What does certified mean? There are four accepted meanings of the adjective ?certified? but only two of which satisfy the needed meaning. To be certified means to be endorsed with authority by an institution or a person with higher
Category:
Site Sponsor
Directory Statistics
Articles: 68222
Categories: 501
Yahoo Entertainment
